Disassembly Instructions
ATA case (Steps 42 - 43)
Step 42 – Attach Front Cover Align the Front Cover so the latches can be secured. Use your foot as a support to align the Front Cover. Once aligned, make sure there are no cables hanging that can be caught in the Front Cover Seam. Secure the latches. ...
Support Brackets and Arm (Steps 35 - 41)
Step 35 – Place Front Cover on Top of Layer 1 of Foam Packing Tray Retrieve the Front Cover from the Lid. Place the Front Cover on top of the Foam Packing Tray with the latch away from you. Step 36 - Remove the Side-Mounted Support Bracket from the ...
Conveyor Sections (Steps 32 - 34)
Step 32 - Inbound Conveyor Table Section Remove the Inbound Conveyor Table Section from the base by unscrewing with two (2) Seven-Lobed Knob – conveyor section fasteners. Store the two (2) Seven-Lobed Knob – conveyor section fasteners in the ...
Table Extension Support Bars (Steps 30 - 31)
Step 30 – Disassemble Table Extension & Stadium Ramp Support (Backstop) Bars Using the 6mm (Grey), loosen the hex screws securing the Stadium Ramp Support Bar to the Table Extension Support bars. These are the Hex Screws located below the Stadium ...
Table Extensions (Steps 28 - 29)
Step 28 – Remove Table Extension Fasteners & Support Bar Fasteners Using the 3/16” Hex Key (White) remove the two (2) hex screws securing the table extension to the conveyor section. The Screws securing the table extension can be found in each corner ...
Stadium Ramp and/or File Platform (Steps 25 - 27)
The following instructions show the Stadium Ramp however, the instructions are the same for the File Capture Platform with the only variation being the File Capture Platform does not have a handle. Step 25 – Remove Stop Pin from Stadium Ramp & Store ...
Store Accessories in Layer 1 of Foam Packing Tray (Step 24)
Step 24 – Store Accessories in Layer 1 of Foam Packing Tray Retrieve Layer 1 of the Foam Packing Tray from the lid and place on top of Layer 2 on the Main Section of the Conveyor Table. Locate the Accessories no longer needed (Positioning Fence and ...
Remove Barcode Scanner (Steps 22 - 23)
Step 22 - Uninstall Barcode Scanner Cradle Using the 5/32” Hex Key, remove the barcode scanner mount from the inbound conveyor section. Step 23 – Unplug and Store Barcode Scanner Unplug the Barcode Scanner from the USB Port labeled Barcode which is ...
Remove Articulating Arms for Cameras with Ring Lights (Steps 20 - 21)
Step 20 – Remove Articulating Mounting Arms for Left (Front) The Articulating Arm for the Right (Back) Camera on the pole located at the back of the base just to the left of the inbound conveyor section as shown in Figure below. Loosen the thumb ...
Remove Cameras w/ Ring Lights (Steps 15 - 19)
Step 15 – Remove Cord Clips for Cameras with Ring from Articulating Mounting Arms Remove the Cord Clips from the Articulating Arm channels by pinching open side of the clips together to disengage them from the Articulating Arm channels as shown in ...
Optional Step - Dowel Pin Reassembly
Optional Step - Dowel Pin Reassembly The Dowel Pin should already be assembled however, if the pin is unscrewed too far it may require reassembly. To reassembly the Dowel Pin, insert the Dowel Pin in the keyhole of the handle. With the Dowel Ping ...
Uninstall Document Cameras (Steps 12 -14)
Step 12 – Unplug and pack the Document Camera Cords Unplug the Document Camera Cords from the standard and stadium document cameras. Roll the cords and place them in Layer 2 of the Foam Packing tray with the Main Power and Ethernet Cords. Step 13 – ...
Monitors (Step 5 - 11)
Step 5 - Get Monitor Storage Case Remove the Monitor Storage Case from the shelves below the main conveyor section. Plate the Monitor Storage Case on top of Layer 2 of the Foam Packing. Remove the cover of the Monitor Storage Compartment. Step 6 - ...
Unplug WIB Unit and Peripherals (Steps 1 - 4)
Step 1 - Disconnect the cords Unplug the cords from the labeled ports on the back of the WIB™ Unit. Step 2 - Unplug Monitors and Top/Aerial Camera Unplug the Power, USB 3.0 B-Male and HDMI cables from the back of the monitors. Refer Monitor Cable ...